BANKSIA TECHNOLOGY PTY., LTD.

MAC CARD 288

Card Type                    Fax, Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I & II
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation Protocol      ITU-T V.17, V.27ter, V.29
Error Correction/Compression MNP5, MNP10, V.42, V.42bis

                                                                      52913

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, ‘+++’, ‘Comma’, A/

  A, B, C, E, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z

  &C, &D, &F, &G, &J, &l, &K, &P, &Q, &S, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \K, \L, \V, %C, %E, %L, %Q

                                S Registers

  S0, S1, S2, S3, S4, S5, S7, S8, S9, S10, S11, S12, S16, S18, S24, S25,
  S29, S30

  S32, S33, S36, S38, S39, S46, S48, S82, S86, S95

                             Special Commands

  *H, -K, -Q, )M, @M, :E, +MS

  Note: See MHI Help file for full command documentation.

                         Proprietary AT Command Set

                        AUTOSYNC ADDRESS CHARACTER

  Type:          Register

  Format:        AT [cmds] S20=n [cmds]

  Default:       0

  Range:         0-255

  Unit:          1 byte

  Description:   Defines the BSC sync character or the HDLC address

  BIT MAPPED REGISTERS

  Register     Default

    S14          138

    S21           4

    S22          117

    S23          55

    S27          73

    S28           0

    S31           2

    S40          107

    S41           3

                          BIT-MAPPED REGISTER S19

  Format:            AT [cmds] S19=n [cmds]

  Default:           Unidentified

  Range:             0-30

  Description:       Controls Hayes AutoSync functions

     Bit      Value                         Function

      0            0   Not used

      1             0   BSC enabled

                   1    HDLC enabled

      2             0   AutoSync disabled

                   1    AutoSync enabled

      3             0   NRZI enabled

                   1    NZI enabled

      4             0   Mark idle enabled

                   1    Flag or syn idle

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        MNP reliable mode enabled

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Modifier                             Function

           J             MNP10 link negotiation enabled

           K             Power level adjustment enabled

           L             Re-dial last number

           P             Pulse dialing enabled

           T             Tone dialing enabled

           !             Modem commanded to go off-hook for amount of
                         time specified in S29 register

           W             Dialing resumed following dial tone detection

           @             Wait for quiet answer

           ,             Dialing paused for amount of time specified in
                         S8 register

           ;             Modem returned to command state after dialing

                               DIALING DELAY

  Type:            Register

  Format           AT [cmds] S6=n [cmds]

  Default:         2

  Range:           0-255

  Unit:            1 second

  Description:     Duration of delay after modem goes off-hook to wait
                   for a dialtone

                              DCE LINE SPEED

  Type:          Register

  Format         AT [cmds] S37=n [cmds]

  Description:   Sets the maximum allowable data exchange rate

    Command                              Function

     S37=0       Automode connection

     S37=1       300bps

     S37=2       300bps

     S37=3       300bps

     S37=5       1200bps

     S37=6       2400bps

     S37=7       V.23 mode

     S37=8       4800bps

     S37=9       9600bps

     S37=10      12.0Kbps

     S37=11      14.4Kbps

     S37=12      7200bps

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports firmware revision, model and interface type

                             RTS TO CTS DELAY

  Type:            Register

  Format           AT [cmds] S26=n [cmds]

  Default:         0

  Range:           0 - 255

  Unit:            .01 second

  Description:     Sets the duration of delay for CTS to respond to RTS
                   status change